Author: James

I'm just this guy, you know? Musician, Software Engineer, Loner-Dottie-Rebel in Asheville, NC

Brakes again.

JamesLeave a comment

I previously fixed the passenger side rear brake and got it adjusted. Now it’s time for me to check the driver side.

One could wonder why the parking brake wasn’t working… I found when clipping the end of the cable back in place, there was a lot of slop and I could imagine in normal use, it could work its way off. When I was recently reviewing old posts here, I noticed when I first looked at the parking brake cables, the driver side cable was tightened down as far as it would go. Maybe this is why.

So, I clipped it back together and re-adjusted the brakes. Tightening that cable all the way back down and applying the parking brake would almost stop the wheel from turning (by hand).

Note to self: The driver side cable is the one that needs to be replaced. Now I know it is just stretched, not broken.

Then I took the passenger side wheel off again and re-adjusted the brakes.

I then tightened the passenger side cable to where I couldn’t turn the wheel by hand with the parking brake lever about 3/4 of the way up. The rear passenger side wheel is now rock solid when the parking brake is on.

I remembered that I had purchased a new dust boot cover for the parking brake assembly. Now that the parking brake is working again, this is the perfect time to install the new boot.

It’s a big stretch and not a comfortable fit. With the heater vent levers pulled through, there was just no flex or stretch to be had.

Let’s move into the back seat for better leverage.

From there, I was finally able to stretch the boot into place.

I had to put in some effort to get the carpet stretched back enough to allow all that excess rubber to be hidden below.

But, I eventually got it. You can see in the pic above, that extra long parking brake cable trying to push through the top of the dust boot.

Now, I can run, stop, and check my mail at the top of the driveway when I get home. The parking brake is essential in the mountains.

This was a much needed win.

Reinstalling the Dash Pad – Part 1

JamesLeave a comment

Back out in the car, it’s time to mount this monstrosity and try to put the end result into perspective. It’s hard to tell how it looks when it’s on its own. You need to see it in context. So, off we go.

First, I mounted those long bolts in the corners.

I put all of the knobs and ash tray back in place.

Some of the knobs didn’t fit properly through the new holes with the additional vinyl pushed down through.

I mounted the grab handle and soon realized some of the cuts I had made in the vinyl below the glove box were too close. That’s a job for another day.

My goal has always been not to have visible patches, where I had to add vinyl after the fact, but that looks really bad. It’s a job for another day.

I don’t remember the ash tray being difficult to open before, but it’s really stiff. Like really stiff. The dash pad and extra layer of vinyl aren’t making contact with it, it’s just super tight.

I had stopped at Lowe’s earlier today and bought some new stainless sheet metal screws and washers. All of those that I removed from the dash pad before were mismatched, some were flat head, some were Phillips, some were shorter and longer.

The screw holes along the bottom weren’t lining up properly as I tried to screw them in and I was quickly losing light, so we’ll call it a day and call that a job for another day.

Wrapping the Dash Pad – Take 2 – Day 2

JamesLeave a comment

OK, we’re back at it.

I’ve got to tighten up some of these loose corners, making little cuts, gluing little bits, and holding them down.

There’s a soft ridge around the hole for the speedometer that isn’t yet taking an acceptable shape.

There were some more gaps over here that needed some more flaps and glue.

It’s starting to look pretty rough around the corners of the glove box. That needs some more cuts and glue.

We’re getting there, slowly, but surely.

I peeled the loose edge of the vinyl back and glued up underneath the long, straight edge along the bottom of the driver side. CHOPSTICK ENGAGE!

The edge was too thick there to clamp with binder clips or clothes pins. I just held it there for a couple of minutes.

Once that set up, I moved on and started cutting, gluing, and clothes pinning some of the detail edges around the gauge cluster and stereo.

There are lots of loose little flaps around the glove box opening. More glue, more binder clips.

Moving on, there are some more loose edges around the driver side which were exposed after cutting off some more excess. Then I remembered I have this ratcheting clamp, which fit nicely on the large bottom corner. Clothes pins fit the rest of the smaller edges nicely.

I have removed quite a bit of excess vinyl, which has just been piling up over here.

Enough of that for the moment, I decided to move back onto the ash tray, trying to find a suitable substitute for the missing spring clip washer thing that’s missing. I started twisting up little mechanics wire fittings, but nothing would grip it properly long term.

That’s the fancy new afghan my mom made for me. She would be so happy to see dirty tools laying on it.

So, then I gave up and glued the face onto the ash tray.

I picked up that little tube of Scotch Maximum Strength Adhesive (ScotchBrand.com link) to serve as a backup for the contact cement when trying to get the vinyl headliner glued back down. I used it liberally behind the face of the ash tray and also on the inside, to cover the pegs.

The face of the ash tray isn’t flat, it has a slight angle, so I couldn’t just clamp it down. I found just the right angle in the vice to put pressure on the contact surface to let that glue set.

Now that the corners of the dash pad are starting to get cleaned up, I decided it would be a good time to re-mount the mounting bolts.

We’re still a little flappy around the stereo opening, so that’s the next place for cuts, glues, and clothes pins.

And then some more clips around loose edges in the glove box opening.

Another big corner, you say? Sounds like another job (the exact same job) for the ratcheting clamp.

Back to the ash tray, now quite a bit later, the glue has held well. Trying to pull the pieces apart, gingerly at first, then with increasing effort, there is a little creaking sound, but it doesn’t budge.

Good enough.

Back to the dash pad, I moved on to opening up the holes for the switches.

It’s kind of creepy looking. Like Blair Witch crosses.

I had been noticing little puddles of glue in places that I hadn’t intentionally put them and was just convinced I was being extra sloppy. Then I saw it…

Death by a thousand little squeezes.

I found some more loose edges around the glove box opening. You can see how much extra glue I was using once I realized the tube was leaking. That’s not a great approach. More of this glue is not better.

Another edge on the glove box opening, just below the new opening for the grab handle.

And now we’re here, kinda rough, but still kinda done, mostly because I’m kinda done with it.

I mounted the matte vintage blue painted grills and speedometer bezel, bending the metal tabs around the back to hold them in place.

It doesn’t look great, but it looks better than it did. That has been an ongoing theme with this car.

Wrapping the Dash Pad – Take 2 – Day 1

JamesLeave a comment

After failing to vinyl wrap the old dash pad the first time, I ordered a new dash pad, which didn’t fit. So… Plan B was always to try wrapping the vinyl again. There’s lots of leftover glue on there.

I ordered some new vinyl (Amazon link), which took a while to get here and is different than what I bought before.

This is some very nice PU Leather Fabrir 2 Yards NEW.

It has a kind of fabric backing instead of the thick 3M adhesive that the previous vinyl (Amazon link) had.

I found that rubbing the dried glue made some of it flake off around the edges. To give my thumbs a rest, I whipped out a little nylon brush that came in a Harbor Freight set (Harbor Freight link). It did a better job than my thumbs.

What I didn’t think of was that is still glue. It’s stuck all over the new vinyl. Luckily, there are 2 Yards NEW and I can just use the other end for today’s project.

Cut to size…

Now SPRAY GLUE ROUND ONE (NEW)!

I sprayed a stripe of 3M Super 77 (Amazon link) three or four inches wide on both the fabric and the dash pad.

I waited for it to get tacky (you know how we do) and started smoothing the vinyl down all around the top edge. Try to leave no wrinkles.

Now SPRAY GLUE ROUND TWO (NEW)!

I flipped the dash pad over, so it was face down (you know how we do). I sprayed another few inches of glue to cover the face and underside, and then waited for it to get tacky.

Apparently, I didn’t learn from dash pad covering part one, because I stretched the vinyl over the whole face, not accounting for the low spots. The glue is drying rapidly and I have to stop to cut holes for the dash and gauge area. I guess I moved quickly enough, because I got it wrapped up pretty well.

No PB Blaster was harmed in the wrapping of this dash pad. It was only there as a prop to stand the dash pad up while the glue was drying. There’s a teeny-tiny wrinkle here that I spent a lot of time working on.

The radio area is not too bad.

Now the first corner wrinkle doesn’t look so bad.

Overall, not too bad.

Now it’s time to start digging into that detail work. Cutting in the edges, another shot of glue – this time the Gorilla Clear Grip (Amazon link).

Loads of wrinkles around the outside edges now.

I need to trim all of the excess to give myself some room to work in there.

Binder clips around one of the side vent openings.

There’s a wide-open corner here, from all of the excess vinyl that was wrapped up in there.

Loaded all the edges up with glue and folded them in.

Binder clips are great for these vent openings.

And all the flat tabs where there are screw holes.

I have soooo many binder clips. I love them.

We’re getting more and more presentable over here. I like it.

The other top corner was as mess as well and needed to be dealt with.

I’ll give it six out of ten. F PLUS.

I needed to get out in the sunlight after being hunched over on the basement floor all day.

So, I headed out and put my big ass to work, getting the rear seat, well, seated. It’s a tighter fit now with all of that padding.

I hope I don’t have to jump start or charge the battery any time soon. Getting underneath that rear seat, then putting it back in place is just about my least favorite thing. Other than dealing with drum brakes.

So I previously spray painted the spring lever on top of the ash tray. The 1634 was shooting silly string and apparently didn’t adhere to this metal, either.

Bummer. So I moved on to trying to lock that other tab in place. I had several pieces of metal, the little clip that speakers mount into. Kind of a washer with a split in it to catch the threads. Anyway, whatever those are called, I had a handful of them (had) and made a few attempts at bending them into shape to grip that little knob (you know how we do). But, nothing held firm for long.

Another job for another day another job for another day another job for another day another job for another day

Let’s button this up…

JamesLeave a comment

I ordered a license plate housing gasket to replace the old, dry, cracked, and broken unit. Let’s add that to the “Easy Wins” list.

And then replaced it.

As I was trying to unscrew the nuts from underneath the engine cover, every one of them just unscrewed the stud from the cover itself. Either way, they all came out easily.

I didn’t think the gasket was going to fit. Using a flat blade screw driver helped stretch it around the edges of the license plate light housing. I was then able to tighten everything down.

Next, I carried both halves of the back seat from the basement and reinstalled them.

Kinda…

I have added a lot of additional padding in the seat base. The additional thickness against the bottom edge of the seat back is too much to fit once the seat back is bolted in place. It will take muscle that I don’t have available at the moment.

Let’s move on to the front.

More effort:

– Jam the drill with self-drilling sheet metal screws through the saddle blanket
– Through the fiberglass kick panels
– Through the actual sheet metal of the car.

Three days later, something inside my wrist-guts still feels out of sorts from the effort.

Anyway, job done.

Aaaaand done.

After the mess with the rear brakes was discovered, I got it all hosed down with brake parts cleaner. Then put it back together and tried adjusting the parking brake cable. Both sides would tighten all the way down without stopping the rear wheels.

Also, this is the first time I’ve had the car started up in around four months. That is by far the longest span it has sat. After four or five tries, she fired right up with no smoke, no warning lights. Ready to go.

She not stop, but will definitely go. I took a few trips back and forth in the driveway. Brakes suck. I’m tired.

Then I loosened the parking brake cables, just to make sure they wouldn’t decide to work at some point when I’m driving and lock up both rear wheels.

Now I move all the way back to the front and begin to reassemble the fresh air box. And packed everything neatly back up under the bonnet.

I’m half convinced that I am missing some parts. The center vent in the dash and the plumbing underneath doesn’t even closely resemble each other. Later, I read an off-topic statement in a post on the samba that said those parts don’t actually mate up.

As it sits right now, there’s no dash pad and no internal vents, so I just reassembled it without the center vent. If anyone has any insight into how this thing goes back together, I would appreciate a comment or a message here. Not that I plan to need the heater any time soon. It was together when I started and I apparently didn’t pay enough attention when disassembling.

Are those hoses that I replaced not actually drain hoses? Are they heater hoses after all? Is it safe to use the washing machine drain hose I purchased to push heat into the cab?

I Give Up.

JamesLeave a comment

I came back out this evening after work with renewed determination to get the dash buttoned up.

After five or ten minutes of wrestling with the piece of garbage that is a $110 rubber dash pad, I threw it out into the yard and got busy reassembling the dash without it.

I don’t fully remember the story, but this plastic trim piece from around the glove box opening has been floating around in the car, laying under the passenger side seat. Screwed it back on using some of the now leftover dash pad screws.

I got most of the dash knobs and the ashtray mounted. The brake test button light thing doesn’t snug up into the hole in the dash panel. It is made to fit into the rubber dash pad.

Since the weather stripping wouldn’t stick to the underside of the bonnet, I instead turned it on its side and used that to replace the old gasket in the fresh air intake box.

Making some progress, getting organizized.

Since that mess of wiring is going to be behind and below everything else, I decided to get the stereo and speaker wires connected and routed through the car.

Not all permanently routed, just enough to be out of the way when I’m driving.

I can’t fully wrap my head around where and how those drain hoses work. My setup doesn’t match any of the pictures and diagrams I’m seeing online.

But that’s a problem for another day.

In the Continuing Saga of the Dash Pad

JamesLeave a comment

After letting this crappy new dash pad upset me so badly before, I decided that I was going to make it work. I won’t be defeated!

I first mounted the large built-in bolts in the top corners, then mounted the grab handle above the glove box. The rest will be just a few little screws across the top and bottom.

It’s WAY too long of a stretch to get that screw from where it is to where it needs to be. Also, the provisions for the dash knobs are all wrong.

The ash tray won’t fit without a big trim.

Since the dash pad is rubber and is pretty flexible, despite having metal plates inside, I removed the grab handle and big bolts in the corners. I figured that it would maybe line up better if I started in the middle and worked my way out.

Nope. I still couldn’t get the screws close enough to mount them. The next surgery I attempted was to cut off the ears around the screw holes, hoping to let it snug up to the windshield.

Instead, I broke my tin snips. After binging Forged in Fire over the course of the last couple of months, I instinctively checked out the grain of the metal where it broke.

Anyway, I finished cutting the ears off. Still too far away!

I realized that the back side of the dash pad doesn’t have enough space for the rounded contour of the metal dash panel and won’t allow it to be pushed on any further.

I’m giving up for the night.

Brakes Again?

JamesLeave a comment

I decided this would be a good time to replace that broken parking brake cable, since the interior is already torn apart.

I got the rear end up in the air and removed the wheel. Flaked off some more undercoating and gave it a quick shot of paint.

I couldn’t get the brake drum off and realized I was going to have to adjust the shoes in. My hands were getting wet with brake fluid as I was feeling around on the back side of the drum to remove the parking brake cable, . Poking my head around to take a look, I saw that it was super cruddy back there. I just rebuilt this brake a couple hundred miles ago!

Let’s not rush into this…

OK, back at it! I had to adjust the brakes in quite a bit to get the drum off. There is a good sized lip around the outside edge. The little T-shaped push pin thing that connects to the spring and cap was gone.

Who even knew that was possible.

I’m all out of brake parts cleaner spray and don’t feel like heading back out to the store today, so I grabbed a new T shaped pin from the front brakes hardware kit I have waiting, wiped everything down, and put it all back together.

Getting that brake shoe locked back in place should fix the parking brake problem. Turns out it wasn’t the cable after all.

Dash Pad Install

JamesLeave a comment

As I mentioned previously, the new dash pad appears to be very high quality, but at a glance, you can see it’s not an exact match to the old one.

When I got started installing it today, it became very apparent this was not going to be plug and play. First, I had to cut off a big section to fit around the ignition switch in the steering column.

Next, the glove box door was bound up and would need a heavy trim.

The kick panel speaker looks pretty good hanging out all casual over there.

In preparing to re-mount the decorative grill plates around the speedometer, I decided to use some of that black vinyl as a backing. The benefit is two-fold. It looks pretty nice, but will also block some air coming in from the poorly sealed front end.

The new dash pad has a speaker hole cut in it and there won’t be a speaker in there anymore.

Time to bring the Matte Vintage Blue out of retirement!

Apparently, I didn’t get them clean enough before spraying the first coat. There are lots of bubbles.

That’s nothing more coats won’t fix.

Defrost hoses

JamesLeave a comment

I picked up this washing machine drain hose at Lowes (Lowes link) and it fits perfectly without the need for clamps. I cut both ends off, then cut it in half. It’s an 8 foot hose, which is way more than I will need, so I can cut each side to fit.

Since Dupli-Color engine enamel has been letting me down lately, I just grabbed this can of generic black primer and gave them a few coats.

The rubber gasket around the fresh air intake box is really hard and crusty and it’s always kind of damp under the bonnet, so maybe this foam window seal will work to bridge the gap.

It’s a nice thought, but the adhesive always lets go immediately on those things, so I don’t have very high hopes.

I pulled the speaker out of the dash. I was wrong before, it’s not a Kicker, it’s a Dual.

The hoses fit tight as a glove!

Told ya.